In a perfect world, current that is sent along a conductive wire is supposed to reach the intended destination in full. However, this does not happen in the real world because some of the current is usually lost along the way. There are different reasons why the current gets lost along the way. In an attempt to prevent the loss of current, resistant sheathing is used to insulate conductive wires. Here are facts regarding Insulation tester.
Sometimes the current is lost if the insulating sheath is made from imperfect materials. Machinery and electric circuits are greatly affected when there is leakage of current due to imperfect cladding. Such a case can be controlled by frequently testing the insulating material to determine its perfectness. Testing the material frequently can help to catch problems in advance before injuries or device failure happens because of loss of current.
A cladding tester is usually used to carry out the testing. The tester tests the resistance of the insulating material to the flow of current thus, determining its integrity. There is very little loss of current for insulating materials of high quality. On the other hand, insulating materials of poor quality will allow large amounts of current to escape.
When measuring the quality of material used to make the sheath, different kinds of current are tested. Absorption, leakage and capacitive currents are the three main types of current tested. The current that occurs immediately when voltage is applied to conductors is referred to as capacitive current.
Capacitive current can be equated to the volume of water that comes out of a pipe immediately a tap is opened. Once the tap is opened, water usually flows out at a higher rate but as the pipe gets filled with water completely, the rate drops rapidly. For the case of a conductive material, the amount of current flow drops once the conductor becomes fully charged.
Absorption current starts out very high and drops just in the same way capacitive current does. However, what differentiates the two kinds of current is the fact that absorption current drops much slowly. The storage of potential energy within the cladding is responsible for the gradual drop in absorption current. In cladding testing using time resistance method, absorption current is a very important part.
Leakage current is also referred to as conduction current. This is a small, steady current that is present both over and through the cladding. If the leakage current increases over time, it implies that the cladding is deteriorating over time too. Insulation test meter usually indicates these increase in leakage current as decrease in resistance.
There is a wide range of cladding testers in the market today. The various models of these products are made by manufacturers located in various countries. The quality of individual testers depends on the manufacturer of the equipment. Also, the various models of these devices in the market are used in different applications. There are testers that are meant for residential testing and those that are meant to be used in industries.
Sometimes the current is lost if the insulating sheath is made from imperfect materials. Machinery and electric circuits are greatly affected when there is leakage of current due to imperfect cladding. Such a case can be controlled by frequently testing the insulating material to determine its perfectness. Testing the material frequently can help to catch problems in advance before injuries or device failure happens because of loss of current.
A cladding tester is usually used to carry out the testing. The tester tests the resistance of the insulating material to the flow of current thus, determining its integrity. There is very little loss of current for insulating materials of high quality. On the other hand, insulating materials of poor quality will allow large amounts of current to escape.
When measuring the quality of material used to make the sheath, different kinds of current are tested. Absorption, leakage and capacitive currents are the three main types of current tested. The current that occurs immediately when voltage is applied to conductors is referred to as capacitive current.
Capacitive current can be equated to the volume of water that comes out of a pipe immediately a tap is opened. Once the tap is opened, water usually flows out at a higher rate but as the pipe gets filled with water completely, the rate drops rapidly. For the case of a conductive material, the amount of current flow drops once the conductor becomes fully charged.
Absorption current starts out very high and drops just in the same way capacitive current does. However, what differentiates the two kinds of current is the fact that absorption current drops much slowly. The storage of potential energy within the cladding is responsible for the gradual drop in absorption current. In cladding testing using time resistance method, absorption current is a very important part.
Leakage current is also referred to as conduction current. This is a small, steady current that is present both over and through the cladding. If the leakage current increases over time, it implies that the cladding is deteriorating over time too. Insulation test meter usually indicates these increase in leakage current as decrease in resistance.
There is a wide range of cladding testers in the market today. The various models of these products are made by manufacturers located in various countries. The quality of individual testers depends on the manufacturer of the equipment. Also, the various models of these devices in the market are used in different applications. There are testers that are meant for residential testing and those that are meant to be used in industries.
About the Author:
Find details about the benefits you get when you use an insulation tester. If you have any questions, see the main page at http://www.rossengineeringcorp.com.
No comments:
Post a Comment